The appearance of advertisements and product information on this site does not constitute an endorsement by Equipment World Magazine, and Equipment World Magazine has not investigated the claims made by any advertiser. Product information is based solely on material received from suppliers.
Wirtgen WR 2000 XL Recycler Tailored for North America
April 8th, 2008
Have someone from Wirtgen America Inc
contact you with more information Click Here
Company: Wirtgen America Inc
The new Wirtgen WR 2000 XL stabilizer/recycler is an updated model of the WR 2000 introduced in 2005. The WR 2000 XL adapts to North American requirements with an industry standard 8-ft.-wide drum (instead of 6-ft., 7-in. on the WR 2000), and cuts up to 20 in. deep with its heavy duty 25MM cutter teeth. This unit also eliminates the cab found on the existing WR 2000.
The all-new WR 2000 XL is a state-of-the-art, 400 hp-class stabilizer/reclaimer which gives heavy contractors and roadbuilders a high-performance alternative to the larger, WR 2400 at 563 HP and the industry-standard, 670-hp WR 2500 S from Wirtgen.
In addition to dry stabilization, it stabilizes with emulsions, and can be equipped with a high capacity water pump for dry soil conditions, or cement or lime stabilization projects. These proven systems have been used on the larger WR 2500/WR 2500 S stabilizer/recyclers for years, and the WR 2000 XL incorporates 40 percent parts in common with its “big brothers”.
Its 6-cylinders OM 457 LA Mercedes engine meets EPA Tier III regulations, with 422 continuous horsepower. Its cutter features a V-belt drive with an automatic belt tensioner with four speeds, from 112 to 181 rpm. This feature delivers maximum hp to the cutter with less maintenance than older-design chain or hydraulic drive systems.
The unique cutter system is a floating hood design with a hardened steel housing, with multiple wear plate inserts to minimize wear. The cutter drum has bolt-on end rings which are easy to service.
Material size is controlled by use of a hydraulically adjustable, managanese-lined breaker bars that can be remotely adjusted by the machine operator to tighten or close down the area between the rotating drum and the impact bars. The machine has all-wheel steering and incorporates the same-size tires both front and rear for maximum tractive effort.
The operator of the WR 2000 XL always has an optimum view of his fiels of operation. He can shift the cabin far beyond the right edge of the machine at the touch of a button, and can also swivel his seat by 90 deg., allowing him to observe the entire right side of the machine. At the same time, he has a free view in those areas of the job site that are in front of him.
The WR 2000 XL can work right up flush to the edges of the surface to be treated, such as curbs or retaining walls. This is possible due to the fact that the wheels on the zero side travel inside the working width and not outside of the milled track. Moreover, the milling and mixing rotor is positioned in the machine, in such a manner that the soil is treated right up to the edge of the machine allowing the WR 2000 XL to work flush to the curb, eliminating time-consuming and costly manual reworking.
In addition, three steering modes make the WR 2000 XL highly manueverable. It can travel with front-axle steering, with steering in the crab mode, or with two steered axles in the “coordinate mode”. The WR 2000 XL has a surprisingly small turning radius of less than 14.7 ft.
Wirtgen America, Inc., Nashville, is the North American arm of the Wirtgen Group, the single-dource marketer of the world”s most technologically advanced lines of asphalt reclaiming and recycling equipment from Wirtgen, asphalt and soil compactors from Hamm Compaction Division, and U.S.-sourced asphalt pavers from VÃ¶gele America Inc. In late 2004 Reinhard Wirtgen, founder of Wirtgen Group, was honored as one of the “Top 100 Private Sector Transportation Design & Construction Professionals of the 20th Century” by the American Road & Transportation Builders Association (ARTBA).