Shock-Proof: How To Avoid Electrocution Accidents During Utility Installs

To download a PDF of this Safety Watch for sharing or printing, click here.

To download a PDF in Spanish, click here.

The accident

A crew was setting anchors in preparation for utility pole placement, using a boom truck with auger. Each anchor was attached to the auger using a coupling, which then used the auger motor to rotate the anchor and screw it into the ground. An anchor began to wobble during the setting process, and a crew member reached out to steady the anchor, unaware the extended boom had touched a 7,200-volt overhead power line.

The anchor was energized, electrocuting the worker. He was pronounced dead from electrocution at the hospital.

The bottom line

A post-accident investigation found the crew member was not a regular employee, but part of a work release program and had no formal training in the utility construction industry. The training was provided on the job, but as a member of the work release program, the worker was unavailable for regularly scheduled safety training meetings.

Additionally, the anchor was a replacement anchor that was more than 2 feet longer than the other anchors used on the project. When the crew tried to set the anchor, the additional length caused it to enter the ground at a difficult angle, creating the wobble that prompted the employee to try steadying the anchor, as well as creating a clearance issue with the overhead power line.

Unnecessary errors

Working around electricity without the proper training, as this crew member did, can be a fatal mistake. Without the proper training, you won’t have the necessary tools to recognize jobsite hazards. The error was compounded by using the longer anchor – material that a jobsite survey would not have accounted for.

Although the 6-foot anchors would have been approved by the competent person conducting the survey, once the 8-foot anchor was substituted, the survey would no longer have been applicable to this jobsite.

Safe steps

  • Training – Attend all training sessions and tailgate talks to make sure you’re ready to begin work.
  • Awareness – Ask what particular hazards the jobsite survey found, and what steps have been taken to mitigate the hazard. You should remain in a safe area while power is disconnected to the lines.
  • Assessment – Before you begin work, walk the site and look for electrical hazards such as overhead power lines. Even if power has been disconnected from the line, stay away. If you’re going to be working around them, always keep an eye on how far your equipment is from these lines, particularly when the boom is extended.

If substitute material is brought onto the jobsite, stop and assess what changes need to be made before continuing work. If there are clearance issues or other hazards created, don’t continue work until the danger is mitigated.

Drawing of a construction worker being electrocuted by a metal pole on a jobsite
High wire hazard

The boom of the excavator was so high it snagged a four-wire utility line carrying power, cable TV, telephone and a neutral wire. The tension on the wires caused by the moving excavator broke the utility pole 70 feet away, bringing all the wires crashing down.

 

Download English Version

Descargue la versión española

Screen Shot 2017-06-16 at 8.27.26 AM
Shocking situations: Working around electricity is serious business

The accident: Two heavy equipment mechanics were using a service truck with a crane to repair a scraper. The crane’s boom came in contact with a 12,000-volt overhead power line. The mechanics were electrocuted, set on fire and died.

Download English Version

Descargue la versión española

0215_Safety_Watch_pix
Drill safe: Preparation is the key to safe horizontal directional drilling

The accident: Crews started working on a gas station renovation in an older residential section of a small town. The plans called for a new water run-off drainage line to be installed from the existing structure to a nearby sewer, but there were no existing prints of the service station’s original utility lines.

Download English Version

Descargue la versión española

Drill_safe_image
Shock-proof yourself: Know the dangers of working around electricity

The accident: A crew was setting anchors in preparation for utility pole placement, using a boom truck with auger. Each anchor was attached to the auger using a coupling, which then used the auger motor to rotate the anchor and screw it into the ground. An anchor began to wobble during the setting process…

Download English Version

Descargue la versión española

Shock_proof_yourself_image
Powered for safety: Use caution when using the tools of the trade

The accident: One man in a five-man crew was using a jackhammer, which was connected to an extension cord. The jackhammer’s worn extension cord came into contact with standing rainwater, and the man, who was not wearing company-issued rubber boots, was electrocuted.

Download English Version

Descargue la versión española

shock3
Electrical problems: Recognize, evaluate and control hazards to stay safe

The accident: A four-man crew was adding space to an existing building by erecting a brick wall. The workers had set up scaffolding, and were pouring grout and inserting rerod into the bricks.

Download English Version

Descargue la versión española

shock2
Prepare not to be shocked: Use common sense when working around electrical hazards

The accident: A crew was working on a landfill gas processing facility installation. While moving a load with a crane, the crane operator touched the boom tip of the crane to an overhead power line with a carrying capacity of more than 12,000 volts.

Download English Version

Descargue la versión española

shock1
Page 1 of 1